Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
The publisher is making several good observations on the subject of A Step-by-Step Guide to Installing a Bathtub overall in this content further down.
Setting up a tub isn't exactly rocket science, yet it does need solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably tough task. If the old bathtub is readily easily accessible, the job can move immediately; if you need to open up a wall to get rid of the old tub as well as position the brand-new bath tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will require a helper to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually qualified yourself for the work and also are comfortable attempting it. Rather than working with a specialist to take over a halfway-completed task, it is far better to consider utilizing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This article will help you install a brand-new bathtub in your bathroom if you have actually already purchased a brand-new bathtub and also don't require to alter the arrangement of your previous water system pipelines.
Your devices as well as material list ought to make up the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the restricted gain access to that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a towel all set for the remaining water that will come from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming during this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Prior to going on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in location in between the tap and also the sink. Safeguard the tap in place with the maker offered backnut. Once the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap ports. The former kind ought to be attached to the tap ends first, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the needed setting. The wood boards are valuable in uniformly spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little points.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the bath tub till the spirit level reads degree.
To mount faucets, fit all-time low of the outermost flexible faucet adapter to the ideal supply pipeline by making a compression join; then do the exact same for the other tap.
Switch on the water system and also check all joints and also brand-new pipework for leaks as well as tighten them if required. Load the bathtub as well as also examine the overflow outlet as well as the regular outlet for leakages.
Finally, repair the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has been utilized at the very least when as this will settle it into its final setting.
Planning for the Installment
To start with, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to stop strain on the bathtub.
Fit the versatile tap adapters to the bottom of both faucets making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final position.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture an inflexible seal, creating the water to pass through the wall surface in between the bath as well as the tiling, causing problems with wetness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the bathtub with water before sealing, to allow for the movement experienced when the tub remains in usage. The sealer can split relatively early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed our piece about How to Install a Bathtub. Thank you so much for spending some time to read our short article. Do you know another person who is excited about the subject? Please feel free to share it. I thank you for reading our article about Installing A Bathtub.
Get professional leak detection today. Report this page